Expert car repairs
at your door

Friction material replacement on floating caliper architecture. Includes anti-rattle clip lubrication and piston boot inspection.

Dual-caliper service with cross-axle pad thickness variance analysis. Includes brake hardware assessment and guide pin re-lubrication.

Rear axle friction renewal with parking brake mechanism preservation. Electronic parking brake retraction required on EPB-equipped vehicles.

Complete rear foundation brake renewal with cast iron rotor replacement. Mandatory electronic parking brake calibration via OBD-II post-installation.

Cast iron braking surface replacement with hub face de-corrosion and lateral runout verification.

Hydraulic actuator replacement with fluid line sealing washer renewal. Piston bore inspection and slide pin lubrication.

Hydraulic circuit evacuation with DOT 4/5.1 verification. ABS modulator valve cycling to evacuate trapped air.

Variable reluctance or Hall-effect wheel speed sensor replacement with air gap verification (0.5-1.5mm typical).

Hydraulic Control Unit replacement requiring high-pressure accumulator depressurisation. ABS coding for vehicle-specific braking characteristics.

Tandem chamber hydraulic component replacement with pushrod adjustment and full system gravity bleed.

Parking brake cable equaliser adjustment for balanced rear wheel application. Ratchet mechanism lubrication.

EPB motor position sensor calibration and clamping force adaptation reset via manufacturer diagnostic tool.

Leading/trailing shoe geometry adjustment with return spring tension verification. Wheel cylinder bore inspection.

Multi-point electronic braking validation including wear sensor recalibration and regenerative braking force mapping (hybrid vehicles).

Front-to-rear hydraulic bias control valve replacement with line fabrication and flare-nut torque adherence.

Double-walled steel hydraulic conduit fabrication with ISO bubble flare or SAE double flare creation.

Precious metal electrode ignition replacement with ceramic insulator integrity check. Dielectric grease application on coil boots.

Transverse V6 rear bank access requiring plenum chamber removal or swivel-socket articulation. Thread chasing preparation.

8-cylinder sequential ignition renewal with coil rail removal on coil-on-plug configurations.

Cylinder head perimeter seal restoration with RTV at cam journal junctions. PCV valve cleaning to prevent recurrence.

Solenoid/piezo metering valve replacement with seal lubrication and rail depressurisation. IMA injector coding post-install.

40kHz cavitation removal of carbon deposits from nozzle sac. Flow rate and spray pattern verified against OEM specs.

Ceramic sheath pre-heating element replacement with current draw verification (10-20A per plug). Anti-seize compound applied.

Wet sump sealing restoration with structural adhesive application and torque-sequence fastening.

Modular filter cap seal replacement with coolant cross-contamination inspection (common BMW N47/N57 failure).

Heat exchanger thermal barrier seal replacement with plate stack inspection. Critical coolant-to-oil barrier integrity.

Vibration isolation elastomeric or hydraulic mount replacement with drivetrain angle preservation.

Multi-ribbed accessory drive belt with automatic tensioner verification and decoupler pulley function test.

High-pressure common rail pressure transducer replacement with system depressurisation protocol.

Submerged electric fuel pump module replacement with float arm calibration and strainer sock renewal.

Multi-layer steel heat exchanger seal with fastener torque-to-yield sequence.

Combustion chamber sealing restoration with torque-to-yield fastener sequence. Surface warpage verification and machining to RA finish spec.

Synchronous belt drive system renewal encompassing automatic tensioner, idler bearings, and water pump seal integrity.

Cam-driven HPFP replacement requiring timing synchronisation. Fuel system priming to prevent airlock.

Coolant circulation component (often belt-driven). Includes thermostat wax pellet verification and seal weep hole inspection.

Vapour-compression refrigeration evacuation with vacuum decay test (500 microns). Refrigerant charge by weight, PAG oil injection, UV dye install.

Low-GWP refrigerant handling with specialised SAE J2842 equipment. Internal heat exchanger systems require specific charge procedures.

Refrigerant heat rejection component with desiccant bag replacement. System evacuation and recharging with oil balance.

Belt drive component with air gap verification (0.3-0.6mm). Coil resistance and thermal fuse integrity.

High/low pressure cutout replacement with Schrader valve depressurisation. Binary/trinary switch verification.

HVAC case thermistor replacement requiring glove box trim removal. Resistance curve verification.

Squirrel cage fan assembly replacement with resistor pack or PWM controller verification.

Speed control module replacement (often integrated with thermal fuse).

Temperature distribution servo motor replacement requiring HVAC control module sync. Full sweep calibration.

Coolant flow control component replacement with O-ring lubrication and hose clamp repositioning.

Heat rejection component replacement with transmission cooler line integrity check (auto vehicles).

Pressurised surge tank replacement with level sensor connector integrity and pressure cap testing.

Electric pusher or puller fan replacement with PWM signal verification for variable speed control.

EPDM rubber conduit replacement with spring clamp upgrade. System bleeding to prevent airlock.

Helical spring replacement requiring controlled compression tool operation. Spring insulator and upper mount bearing inspection.

Rear axle suspension component renewal with axle stand positioning for load-bearing simulation.

Hydraulic damping component replacement with nitrogen gas charge preservation. Bumper stop and dust boot renewed.

Stabiliser bar end link replacement with ball joint socket integrity verification.

Torsional spring mounting bushing renewal. Polyurethane upgrade option for enhanced cornering stiffness.

Suspension geometry component with rubber bushing preload specification (tighten at ride height).

Preloaded hub assembly with axle nut torque spec (150-250 Nm typical). ABS sensor clearance verification.

Tapered roller bearing interference fit replacement requiring hub carrier removal. Hydraulic press required.

MacPherson strut cartridge and spring with camber plate orientation preservation. Top mount bearing preload.

Comprehensive front axle replacement including control arms, links, and bushes. Includes geometry check.

Steering linkage ball joint replacement with tie rod thread counting for toe-in preservation.

Steering gear replacement with tie-rod transfer and rack centering procedure. Full system bleed.

Rack and pinion internal linkage replacement requiring boot clamp removal. Geometry preservation critical.

Constant velocity joint replacement with axle shaft removal. Molybdenum disulfide grease packing and boot clamping.

Thermoplastic elastomer accordion boot replacement with joint cleaning and grease contamination assessment.

CV axle shaft assembly replacement with stub shaft spline engagement and ABS reluctor ring transfer.

Two-piece propshaft centre bearing with phasing alignment (maintain factory clocking).

RWD propshaft carrier bearing replacement with spline engagement inspection and U-joint articulation test.

Manual transmission selector mechanism renewal with quadrant adjustment and detent ball inspection.

Powertrain isolation component with drivetrain angle preservation.

Hydraulic control sump removal with filter element and seal replacement. Magnet debris analysis.

Complete hydraulic circuit fluid exchange via cooler line pressure. 12-15L exchange capacity.

CVT push-belt or chain replacement requiring pulley disassembly. Clean room environment for steel belt handling.

Electro-hydraulic control module with DSG valve body. DQ200/DQ250 fluid verification and basic settings.

Fluid coupling replacement requiring transmission removal. Stator clutch and TCC solenoid testing.

Friction element and pressure plate replacement with DMF inspection. Release bearing preload and hydraulic bleed mandatory.

Torsional vibration damper replacement with spring pack wear assessment. Critical bolt torque-angle specs.

Complete drivetrain refresh: friction system + rotational inertia management. Includes rear main seal inspection.

Hydraulic actuation component with pushrod adjustment and pedal feel verification.

External slave cylinder replacement with bleeding and engagement point verification.

Internal concentric slave requiring gearbox removal. Critical alignment with release fork.

Manual transmission selector position sensor replacement with adjustment verification.

Standard flooded lead-acid battery replacement for non-start-stop vehicles. Includes terminal cleaning and protective grease application.

Enhanced Flooded Battery for entry-level start-stop systems. Includes BEM coding for charging profile registration.

Absorbent Glass Mat battery for premium start-stop vehicles (BMW, Audi, Mercedes). Includes mandatory BEM coding via diagnostic interface — critical for brake energy recuperation compatibility.

High-performance Li-ion or LiFePO4 retrofit. Requires custom mounting and ECU compatibility verification.

Put petrol in your diesel or diesel in your petrol? DO NOT START THE ENGINE. We drain the contaminated fuel, flush the fuel lines, and refill with the correct fuel so you can drive away safely. Mobile service — we come to you wherever you are.

Charging or cranking system component with decoupler pulley inspection or shim adjustment. Voltage/current verification.

Belt-driven charging component with clutch pulley function test. Voltage regulation curve verification under load.

Cranking motor replacement with pinion engagement verification and current draw testing (100-200A typical).

Comprehensive exterior lamp renewal including headlights, sidelights, indicators, and brake lights with dielectric grease application.

Single lamp replacement with halogen oil contamination prevention. LED thermal management verification on solid-state systems.

Secondary ignition component replacement with primary circuit resistance testing and misfire monitoring verification.

Hot-wire/hot-film element replacement with contamination assessment to prevent recurrence.

Thermal element restoration with MAF-specific cleaner (not brake cleaner). Signal output verification via live data.

Thermistor component replacement with O-ring lubrication and resistance curve verification.

Hall-effect timing reference sensor replacement with synchronisation signal verification.

Engine speed reference sensor with air gap verification (0.5-1.5mm) and reluctor ring inspection.

Intake manifold pressure reference sensor with port inspection for carbon blockage.

High-frequency acoustic warning device with amperage draw verification (3-5A typical).

Circuit protection element inspection with resistance testing and underlying short circuit diagnosis.

Door glass actuator mechanism replacement with anti-pinch sensor calibration where equipped.

Software-initiated regeneration raising exhaust temps to 600°C+ for soot oxidation. Ash accumulation reset.

Particulate filter differential pressure transducer replacement with calibration verification.

Emissions control device with O2 sensor preservation. Efficiency verification via post-cat sensor waveform.

Acoustic attenuation chamber replacement with clamp or weld attachment.

Intermediate exhaust component with flex joint inspection.

Elastomeric isolation component replacement with graphite lubricant.

Lambda sensor replacement with anti-seize on stainless bosses. Post-cat waveform verification.

EGR component with intake manifold decarbonisation. Pintle valve position learning post-install.

Heat exchanger replacement with coolant evacuation and pressure testing.

Pneumatic or electronic boost control replacement with hose integrity check.

SCR system feedback sensor replacement with heating circuit calibration via OBD.

DEF system pump/injector/tank heater replacement with 32.5% urea concentration verification.

Multi-layer steel heat expansion joint replacement with torque-to-yield sequence on turbo housings.

Li-ion pack cell voltage deviation analysis using proprietary diagnostic protocols. Thermal imaging for hot spot detection.

Forced air cooling component with HV service disconnect procedure (Category 0 PPE required).

Power electronics thermal management fluid exchange with isolation procedure. Low-conductivity coolant (<5 μS/cm).

DC-AC/DC-DC power conversion module replacement with HV safety lockout/tagout. Capacitor discharge verification (<60V).

HV-to-12V conversion module replacement. Steps down 400V/800V to 12V. HVIL verification post-install.

Orange conduit integrity verification with insulation resistance testing (>1MΩ typical). Shielding continuity check.

AC charging inlet with pilot signal wire verification and proximity detection switch calibration. Weather seal critical.

Energy recuperation verification: generator torque output, pedal sensor correlation, blending algorithm function test.